Efco TG 2600 XP Instruction Manual Page 1

OPERATOR’S INSTRUCTION MANUALMANUEL D’UTILISATION ET D’ENTRETIENMANUAL DE INSTRUCCIONESenfresTG 2600 XP(1.55 cu.in) - TG 2750 XP(1.55 cu.in)Efco TG26

10enSAFETY RULESPrecautions to Reduce Vibration Risk• The hedge trimmer is provided with anti-vibration (AV) system; never alter or modify it.• Wear g

11enOPERATIONFueling (Do Not Smoke!) (Fig. 16)This product is powered by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle oil. Pre-mix u

12enOPERATIONFilling the Tank (Fig. 18)WARNING: Follow safety instruction for fuel hand-ling. Always shut off engine before fueling. Never addfuel to

13enOPERATIONWork Area PrecautionsWARNING: Cut only hedges or materials made fromwood. Do not cut metal, plastics, masonry, or non-wood building mater

14enOPERATION• Make sure that the throttle lever works properly.• Fill the carburetor by pushing primer bulb a couple of times (A,Fig.23).• Put the ON

Difficult Starting (or starting a flooded engine)The engine may be flooded with too much fuel if it has not startedafter 10 pulls. Flooded engines can

16enOPERATIONWorking Techniques General Working InstructionsWARNING: Do not cut during periods of high wind orheavy precipitation.WARNING: Never cut,

17enOPERATION• If any foreign object is hit or if high vibrations occur stop themachine immediately. Disconnect the HT lead from the sparkplug. Check

18MAINTENANCEMaintenance ChartPlease note that the following maintenance intervals apply for normal operating conditionsonly. If your daily work requi

19MAINTENANCEBlade MaintenanceClean (don’t use grease solvent) any resin and plant residue fromthe blades before and after using the machine.WITH NEW

To correctly use the hedge trimmer and prevent accidents, do not start work withouthaving first carefully read this manual. You will find explanations

en3940414220MAINTENANCECarburetor AdjustmentThis engine is designed and manufactured in order to comply withEPA (Environmental protection Agency) Phas

21MAINTENANCECooling SystemTo keep the working temperature as low as possible the machineis equipped with a cooling system.The cooling system(Fig.43)

22MAINTENANCEGear HousingThere is a grease nipple and a plug for filling lubricant on the gearhousing (Fig.46). Use a grease gun to fill with grease.

Using Troubleshooting ChartWARNING: Always stop unit and disconnect spark plug before performing all of the recommendedremedies below except remedies

TG 2600 XP - TG 2750 XPENGINE:Displacement: 2.15 cu. in (24.5 cc)Bore: 1.34 in (34 mm)Stroke: 1.10 in (28 mm)PERFORMANCE:Idle Speed: 2,800 RPMWOT (Wit

Mod. 58040378 - Apr/2007 - CENTROFFSET R.E. - Printed in ItalyEMAK s.p.a. - Member of the YAMA group42011 BAGNOLO IN PIANO (REGGIO EMILIA) ITALYEMAK

3PRODUCT IDENTIFICATIONHedge Trimmer Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4S

4Hedge Trimmer Components1 - Blade2 - Blade Guard3 - Hand Guard4 - Front Handle5 - Air Filter Cover6 - Idle Speed Screw7 - Fuel Tank Cap8 - Muffler9 -

5enSAFETY- This symbol indicates Warning, andCaution.- Your manual contains special mes-sages to bring attention to potentialsafety concerns, machine

6enSAFETYWARNING: Exposure to vibrations through prolonged use of gasoline powered hand toolscould cause blood vessel or nerve damage in the fingers,

17enSAFETY RULESBasic Safety Precautions • Read this manual carefully until you completely understand andcan follow all safety rules, precautions, and

8enSAFETY RULESFuel Handling WARNING: Gasoline is an extremely flammable fuel.Use extreme caution when handling gasoline or fuelmix. Do not smoke or b

9enSAFETY RULES• Only use the hedge trimmer in well-ventilated places, do notoperate the hedge trimmer in explosive or flammable atmo-spheres or in cl