Efco Dorma RTS 88 User Manual

 Storefront –dorma rts 88 Concealed overhead closer supplementInstallation InstructionsPart NO. Y013 February 2013

PAGE 8BAB 7/01STEP F.{STB9} #12-11 X 1/2"PL-RH SMS 18-8 A(SUPPLIED W/ K173){8428} (4" DOOR HEADER) SHOWN{8429} (4 1/2" DOOR HEADER)HING

PAGE 9BAB 7/01A. BUTT HINGE, CONTINUOUS HINGE, CENTER PIVOTS 1. CLOSER PREP AND INSTALLATION STEPS FOR 1 3/4" AND 2" HEADER/T’BA

BAB 7/01PAGE 10INSTALLATION OF THE CLOSER IS IDENTICAL FOR THE 1 3/4" AND 2" HEADERS. THE 2" HEADER IS SHOWN IN THE FOLLOWING DETAILS.

BAB 7/01PAGE 11D. LOCATE THE C.O.C. COVER PLATE INTO THE HEADER/TRANSOM BAR CUTOUT AND FASTEN THE COVER PLATE INTO PLACE WITH THE SUPPLIED SCREWS TH

BAB 7/01PAGE 12ANGLE BRACKET (C)1/4-20 X 1/2" (C)SPACER BLOCK-4 1/2" HEADER/T’BAR ONLY-{SUPPLIED IN K501 AND K500}MOUNT {4" - K497 CONT

BAB 7/01PAGE 13MOUNTSHEAR BLOCK {K173}MOUNT SCREW LOCATIONSPACER BLOCK4 1/2" HEADER ONLY{FU09}"F" CLIP (C)4 1/2" HEADER/TRANSOM BA

BAB 7/01PAGE 14DORMA RTS 88 OVERHEAD CLOSERCOVER PLATES{K492 PKG. MILL}{K495 PKG. CLR}{K496 PKG. BRZ}HINGE/ PIVOT JAMB4 1/2" HEADER/TRANSOM BAR (

PAGE 15BAB 7/01STEP B.1/4" ID WASHER (C)1/4"-20X1/2" HX-MS (C)#12-24X3/4"PL-FH-MS 18-8 UC{M100 - CLR}{M108 - BRZ}STEP A.MOUNTINGBL

BAB 7/01PAGE 16NOTE:THE FINISH ON THE ATTACHMENT SCREWS SHOULD MATCH THE FRAME’S FINISH.#12-24X3/4"PL-FH-MS 18-8 UC- SEE NOTE BELOW -{M100 - CLR}

PAGE 17BAB 7/01F. LOCATE THE C.O.C. COVER PLATE INTO THE HEADER/T’BAR CUTOUT AND FASTEN THE COVER PLATE IN PLACE WITH THE SUPPLIED FASTENERS AT THE A

THESE INSTRUCTIONS USE FLUSH GLAZE STOREFRONT AS A BASISFOR DETAILING. THE TRANSOM BAR PREPS WILL BE THE SAMEFOR ALL OTHER FRAMING SYSTEMS THAT REQUI

CLOSER SLIDE ARM(BY DORMA)SLIDE BLOCK(BY DORMA)BUSHING(BY DORMA){9914}SLIDE TRACK(BY DORMA)DOOR STOPSHIM BY EFCODOOR STILE-IF REQUIRED-TOP RAIL{K496}

PAGE 19BAB 7/01B. CENTER PIVOTSSPACER BLOCKMOUNT4" HEADER{K497} CONT. AND BUTT HINGES{K498} CENTER PIVOTS4 1/2" HEADER{K928} CENTER PIVOTS

BUSHINGSHIM BY EFCO-IF REQUIRED-TOP RAILSLIDE TRACK(BY DORMA)CUSHION9914-DOOR STOPSLIDE TRACK(BY DORMA)(BY DORMA)(BY DORMA)SLIDE BLOCKK435 FU03 - R

PAGE 21BAB 7/01STEP B.VALVE "B"STEP A.VALVE "A"SPINDLESECTION VI CLOSER ADJUSTMENT A. CHECK THE LATCHING SPEED OF THE DOOR AND

BAH 8-9-04PAGE 1SECTION I PARTS IDENTIFICATIONSHEAR BLOCK w/ SCREWS4" & 4 1/2" HEADER(S402){K173}SHEAR BLOCK w/ SCREWS(S401 & S402){

PAGE 2BAB 7/01SECTION I PARTS IDENTIFICATION (CON’T)COVER PLATE w/ OFFSET PIVOTS{FT20} RIGHT HAND MILL{FT26} LEFT HAND MILL{FU02} RIGHT HAND CLR{FU04}

BAB 7/01PAGE 3A. BUTT HINGE, CONTINUOUS HINGE, AND CENTER PIVOTS 1. 1 3/4" OR 2" HEADER/T’BAR INSTALLATION STEPS SECTION II HEAD

PAGE 4BAB 7/01NOTE: 2" HEADER/T’BAR PREPARATION (SHOWN) 1 3/4" HEADER/T’BAR PREPARATION SIMILAR FOR SINGLE DOORS AT

PAGE 5BAB 7/01A. BUTT HINGE, CONTINUOUS HINGE, AND CENTER PIVOTS (CON’T) 2. 4" OR 4 1/2" HEADER/T’BAR INSTALLATION STEPS SECTION

PAGE 6BAB 7/01A. BUTT HINGE, CONTINUOUS HINGE, AND CENTER PIVOTS (CON’T) 1. 4" OR 4 1/2" HEADER/T’BAR INSTALLATION STEPS (CON’T)

BAB 7/01PAGE 7B. OFFSET PIVOTS 2. 1 3/4" OR 2" HEADER/T’BAR INSTALLATION STEPSSECTION II HEADER/TRANSOM BAR INSTALLATION (CON’T)STEP B